Page 1 of 2

USB BLE-Link: No AT Response

Unread postPosted:Wed Oct 09, 2019 2:16 pm
by chris.ricketts
Hi,

I have a Bluno USB BLE-Link dongle which I have updated to the 1.97 firmware (SBL_Blelinkv1.97.bin).

It does not respond with "Enter AT Mode" when I send "+++".

Image

It also didn't respond before I updated the firmware.

I have tried it with 3 different dongles.

Any ideas as to how to fix this?

Thanks in advance,
crick

Re: USB BLE-Link: No AT Response

Unread postPosted:Thu Oct 10, 2019 7:33 am
by nana.wang
Hi Crick,
Thanks for your support.
Could you please offer the SKU No. and have you read through the wiki page related?
If not, please read it first.

Re: USB BLE-Link: No AT Response

Unread postPosted:Thu Oct 10, 2019 9:55 am
by chris.ricketts
SKU: TEL0073

Yes, I have read through both of these wiki pages:
https://wiki.dfrobot.com/BLE-Link__SKU_TEL0073
https://wiki.dfrobot.com/Bluno_SKU_DFR0267

Re: USB BLE-Link: No AT Response

Unread postPosted:Thu Oct 10, 2019 12:10 pm
by chris.ricketts
Also, when using the BlunoBasicDemo Android app to test the BLE-Link TEL0073 dongles - data sent to the dongle does not appear in the Arduino Serial monitor but data sent from the serial monitor does appear in the "Received Data" section of the app.

Does this indicate that the BLE-Link TEL0073 has an issue with writing to the serial port it creates on the PC?

Re: USB BLE-Link: No AT Response

Unread postPosted:Fri Oct 11, 2019 3:02 am
by nana.wang
Hi Chirs,
Got it. And we have a post in Chinese witch may help you solve it. But I need time to translate it.
Once it is translated, I will share it with you.

Re: USB BLE-Link: No AT Response

Unread postPosted:Mon Oct 14, 2019 3:28 am
by nana.wang
Hi we found that if the IO espansion board is in RUN mode, which means the RX/TX are occupied and the data cannot be sent.
So please try change the mode, and chck the result.

Re: USB BLE-Link: No AT Response

Unread postPosted:Mon Oct 14, 2019 9:54 am
by chris.ricketts
Hi,

I made a mistake with the SKU. It is: TEL0087 - https://www.dfrobot.com/product-1220.html
I am sorry for wasting your time this far.

Just to clarify:
Sending "+++" does respond with "Enter AT Mode".
I can receive data sent from the TEL0087 to the BlunoBasicDemo Android app.
I do not receive data sent from the Android app to the TEL0087 - i.e. No data received on the serial (COM) port.
It appears that TX is working but RX is not working.

Re: USB BLE-Link: No AT Response

Unread postPosted:Mon Oct 21, 2019 5:31 am
by nana.wang
Please try uploaing Blink to the UNO.

Re: USB BLE-Link: No AT Response

Unread postPosted:Mon Oct 21, 2019 9:56 am
by chris.ricketts
Hi, I am not using an UNO.

I am just using TEL0087 - https://www.dfrobot.com/product-1220.html

It is not working with your demo android app or entering AT mode.

Re: USB BLE-Link: No AT Response

Unread postPosted:Tue Oct 22, 2019 9:35 am
by nana.wang
Okay, please uploaing Blink to the UNO to test it first, if it goes ok the sensor is alright.