Make your unique DIY projects with 1500+ Arduino,modules,sensors, robot components/parts and kits.
Analog Sensor Cable for Arduino (10 Pack) Introduction
The analog sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our analog sensor to the IO board.
This price includes 10 pieces of cables.
Latest Update: Change the analog sensor extension pin mapping to be compatible with the latest IO expansion shield and Romeo analog sensor expansion pinout.
Arduino Jumper Cables (M/M) (65 Pack) Introduction
Breadboard jumper wire 65 pcs pack (Male to Male header). Including 4 different length:200mm,165mm,125mm and 80mm.A must have component for breadboard.
240mm (9.4in) x5
200mm (7.9in) x5
150mm (5.9in) x8
110mm (4.3in) x49
Arduino Jumper Cables (M/M) (65 Pack) x1
Breadboard Jumper Cables High Quality (30 Pack) Introduction
This is a DFRobot exclusive! This is a high quality jumper cable. Hand made with 22AWG multistrand wire and sturdy male pins. Each jumper cable has an approximate 210mm lenght.Each pack comes with ten jumper cables(different colors available).
These jumper cables are perfect for bread boards, Arduino, or any other application where you might be frequently plugging and unplugg..
Digital Sensor Cable For Arduino (10 Pack)
The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board.
This price includes 10 pieces of cables.
Length:30cm (12 in)
One Servo Type connector with Signal, GND PWR.
One 3 Pin ..
Jumper Wires (F/M) (65 Pack) Introduction
Jumper wires are one of the most important gear component for the tinkerer. Often understimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really needed, doubt not, this is at some point or another always used. Wire or pieces or wire are basic, even for the non-often tinkerers. Jumper wires are not just fitted for ..
Jumper Wires 9" F/F (10 Pack) Introduction
These are 9"(23cm) long jumper wires terminated as female to female. Use these to connect from any male header on any board such as DFRobot IO Shields. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of ten jumpers (colors may vary).
We use these wires for everything! They work great with breadboards, Arduino, and really any 0...
U Shape Jumper Wires (Box) Introduction
This is a time saving kit of jumper wires - cut, stripped,bent 90 degree on both ends for easy insertion and your prototyping pleasure.Make your prototyping neat and looks nicer, The box included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each. Various colors of jumper wire, perfectly fit for..
USBtinyISP-Arduino bootloader programmer Introduction
This is a USB AVR programmer supported by offical Arduino IDE. Once the Arduino has lost its bootloader for some reasons, use this programmer to reburn the bootloader and save the dead Arduino.
This programmer works really well for ATmega168 and ATmega328 and should work with all the AVR micros supported by AVRDUDE. Both 10-pin and 6-pin targets supported (cable included) ..
Gravity: Analog Adjustable Infrared Proximity Sensor For Arduino Introduction
This is an Arduino infrared distance sensor. It has an adjustable detection range, 3cm - 80cm. It is small, easy to use, assemble, and inexpensive. Useful for robotics, interactive media, industrial assembly line, etc. Infrared wave length is part of the Sun's natural light spectrum. While is a nice fit for indoor projects, outdoors with plenty of sun light and reflective..
2x1A DC Motor Shield for Arduino
This Motor shield for Arduino uses L293 chip which allow to drive two 7-12V DC motors with maximum 1A current each channel. This shield can be directly stacked on standard Arduino Uno and Arduino Mega.
2 way 7-12V motor drive
Up to 1A current each way
PIN 4,5,6,7 are used to drive two DC motors
Support PWM speed control
3.7V Polymer Lithium Ion Battery - 1000mAh Introduction
These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 1000mAh! Comes terminated with a standard 2-pin JST connector - 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a sp..
7.4V Lipo 2500mAh Battery (Arduino Power Jack) Introduction
This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anything that requires a small battery with a lot of punch. The voltage is low enough not to tax your regulating circuits, and the discharge rate is high enough to accommodate a lot of electronics and motors.
We customized it by using an Arduino Com..
9g micro servo (1.6kg) Introduction
Do you need a servo for a tiny little project? Or are you seeking for an affordable solution? This mini servo is quite impressive, it does quite the job for a large range of tasks. Only weights 9 grams and gives you a 1.6kg cm torque. Pretty strong regarding its size. Suitable for Beam robots and other automation tasks. Keep in mind that if you need some heavy lifting you ..
ATmega328 Chip with Arduino Bootloader Introduction
The name says it all on this one. An ATmega328 in DIP package, pre-loaded with the Arduino (16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board.
To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. If you are not c..
Ball Caster Metal-MiniQ Introduction
This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.
The total height of this ball caster is 0.4" with no spacers. You can also adjust the height by adding the spacers.The ball caster is used in our widely popular MiniQ sereis.
You can buy this ite..
Gravity: Analog Ambient Light Sensor For Arduino Introduction
Here comes DFRobot's new Analog Ambient Light Sensor for Arduino or Raspberry Pi. Brand new design and much more convenient to use. This sensor help you to detect the light density and reflect the analog voltage signal back to Arduino controller. You can set the threshold of voltage level to trig other unit on Arduino project.
We also use the enviromental PT550 light sensor..