Analog Sensor Cable for Arduino (10 Pack) Introduction
The analog sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our analog sensor to the IO board.
This price includes 10 pieces of cables.
Latest Update: Change the analog sensor extension pin mapping to be compatible with the latest IO expansion shield and Romeo analog sensor expansion pinout.
Arduino Jumper Cables (M/M) (65 Pack) Introduction
Breadboard jumper wire 65 pcs pack (Male to Male header). Including 4 different length:200mm,165mm,125mm and 80mm.A must have component for breadboard.
240mm (9.4in) x5
200mm (7.9in) x5
150mm (5.9in) x8
110mm (4.3in) x49
Arduino Jumper Cables (M/M) (65 Pack) x1
Breadboard Jumper Cables High Quality (30 Pack) Introduction
This is a DFRobot exclusive! This is a high quality jumper cable. Hand made with 22AWG multistrand wire and sturdy male pins. Each jumper cable has an approximate 210mm lenght.Each pack comes with ten jumper cables(different colors available).
These jumper cables are perfect for bread boards, Arduino, or any other application where you might be frequently plugging and unplugg..
Digital Sensor Cable For Arduino (10 Pack)
The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our digital sensor to the IO board.
This price includes 10 pieces of cables.
Length:30cm (12 in)
One Servo Type connector with Signal, GND PWR.
One 3 Pin ..
Jumper Wires (F/M) (65 Pack) Introduction
Jumper wires are one of the most important gear component for the tinkerer. Often understimated, but one of the first things to miss. If you are starting to assemble your tinker gear and wondering if this is really needed, doubt not, this is at some point or another always used. Wire or pieces or wire are basic, even for the non-often tinkerers. Jumper wires are not just fitted for ..
Jumper Wires 9" F/F (10 Pack) Introduction
These are 9"(23cm) long jumper wires terminated as female to female. Use these to connect from any male header on any board such as DFRobot IO Shields. Multiple jumpers can be connected next to one another on a 0.1" header. Comes in one pack of ten jumpers (colors may vary).
We use these wires for everything! They work great with breadboards, Arduino, and really any 0...
U Shape Jumper Wires (Box) Introduction
This is a time saving kit of jumper wires - cut, stripped,bent 90 degree on both ends for easy insertion and your prototyping pleasure.Make your prototyping neat and looks nicer, The box included with this kit are 14 various lengths of 22AWG wire - 2, 5, 7, 10, 12, 15, 17, 20, 22, 25, 50, 75, 100, and 125mm - 10 pieces of each. Various colors of jumper wire, perfectly fit for..
3.7V Polymer Lithium Ion Battery - 1000mAh Introduction
These are very slim, extremely light weight batteries based on the new Polymer Lithium Ion chemistry. This is the highest energy density currently in production. Each cells outputs a nominal 3.7V at 1000mAh! Comes terminated with a standard 2-pin JST connector - 2mm spacing between pins. These batteries require special charging. Do not attempt to charge these with anything but a sp..
7.4V Lipo 2500mAh Battery (Arduino Power Jack) Introduction
This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anything that requires a small battery with a lot of punch. The voltage is low enough not to tax your regulating circuits, and the discharge rate is high enough to accommodate a lot of electronics and motors.
We customized it by using an Arduino Com..
ATmega328 Chip with Arduino Bootloader Introduction
The name says it all on this one. An ATmega328 in DIP package, pre-loaded with the Arduino (16MHz) Bootloader. This will allow you to use Arduino code in your custom embedded project without having to use an actual Arduino board.
To get this chip working with Arduino IDE, you will need an external 16MHz crystal or resonator, a 5V supply, and a serial connection. If you are not c..
Ball Caster Metal-MiniQ Introduction
This ball caster used for MiniQ robot is a white ABS housing, a 3/8" diameter metal ball, two spacers (1/16" and 1/8" thick), and two #2 screw sets.
The total height of this ball caster is 0.4" with no spacers. You can also adjust the height by adding the spacers.The ball caster is used in our widely popular MiniQ sereis.
You can buy this ite..
Medium Bread Board Self Adhsive Introduction
This is a medium size breadboard with 600 tie points. It has strong, self-adhesive backing. It is ideal for high frequency and low noise circuits.
Size:170*65mm (6.7x2.6 in)
Suitable for 0.3-0.8 mm (0.01x0.03 in) wire
Medium Bread Board Self Adhsive x1
Mega Prototyping Shield for Arduino Mega Due Introduction
This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy. Some assembling and soldering is required!Some assembling and soldering is required!
Reset button up top
Lots of GND and +5V rails
DIP prototyping area makes it easy to add more chips
Mini Bread Board Self Adhesive Introduction
This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield shown below. Strong, self-adhesive backing. Measures 1.8"x1.4".
170 tie point breadboard
17 x 5 x 2 points
Mini Bread Board Self Adhesive x1
Prototyping Shield for Arduino Introduction
This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch or other components, it also comes with a mini Arduino breadboard that can stick on the prototyping shield that make the project look tidy and fancy. The working area of this protoshield has DIP prototyping area sutiab..
0.1″ (2.54 mm) Arduino Male Pin Headers (Straight Black 10pcs) Introduction
This is a blue colored 40 Pin 2.54 mm（0.1"） single row pin header strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino connectors. The standard spacing allows use with solderless breadboards, perforated prototyping PCBs, female headers, and our premium and pre-crimped jumper wires. The single-row header strips can easily be snapped into smaller st..