TCS3200 Color Sensor (SKU:SEN0101)

From DFRobot Electronic Product Wiki and Tutorial: Arduino and Robot Wiki-DFRobot.com

Introduction

TCS3200 GBB Color Sensor For Arduino is a complete color detector, including a TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 can detect and measure a nearly limitless range of visible colors. Applications include test strip reading, sorting by color, ambient light sensing and calibration, and color matching, to name just a few.

The TCS3200 GBB Color Sensor For Arduino has an array of photo detectors, each with either a red, green, or blue filter, or no filter (clear). The filters of each color are distributed evenly throughout the array to eliminate location bias among the colors. Internal to the device is an oscillator which produces a square-wave output whose frequency is proportional to the intensity of the chosen color.

Specifications

  • Single-Supply Operation (2.7V to 5.5V)
  • High-Resolution Conversion of Light Intensity to Frequency
  • Programmable Color and Full-Scale Output Frequency
  • Power Down Feature
  • Communicates Directly to Microcontroller
  • S0~S1: Output frequency scaling selection inputs
  • S2~S3: Photodiode type selection inputs
  • OUT Pin: Output frequency
  • OE Pin: Output frequency enable pin (active low), can be impending when using
  • Support LED lamp light supplement control
  • Size: 28.4x28.4mm

PinOut

Color Sensor 1.jpg
Pin Name I/O DESCRIPTION
GND(4) Power supply ground. All voltages are referenced to GND
OE(3) I Enable for fo (active low).
OUT O Output frequency (fo).
S0,S1(1,2) I Output frequency scaling selection inputs.
S2,S3(7,8) I Photodiode type selection inputs
VDD(5) Supply voltage













Tutorial

Connection Diagram

The TCS3200 Color Sensor


Wiring instructions
VCC——5V GND——GND
S0——D3 S1——D4
S2——D5 S3——D6
OUT——D2

S0,S1,S2,S3

To TCS3002D, when choose a color filter, it can allow only one particular color to get through and prevent other color. For example, when choose the red filter, Only red incident light can get through, blue and green will be prevented. So we can get the red light intensity. Similarly ,when choose other filters we can get blue or green light.

TCS3002D has four photodiode types. Red , blue, green and clear, reducing the amplitude of the incident light uniformity greatly, so that to increase the accuracy and simplify the optical. When the light project to the TCS3002D we can choose the different type of photodiode by different combinations of S2 and S3. Look at the form as follows.

S0 S1 OUTPUT FREQUENCY SCALING (fo)
L L Power down
L H 2%
H L 20%
H H 100%

TCS3002D can output the frequency of different square wave (occupies emptiescompared 50%),different color and light intensity correspond with different frequency of square wave. There is a relationship between the output and light intensity. The range of the typical output frequency is 2HZ~500KHZ. We can get different scaling factor by different combinations of S0 and S1. Look at the form as follows.

S2 S3 PHOTODIODE TYPE
L L RED
L H BLUE
H L Clear (no filter)
H H GREEN

Sample Code

int s0=3,s1=4,s2=5,s3=6;
int out=2;
int flag=0;
byte counter=0;
byte countR=0,countG=0,countB=0;
void setup()
 {
 Serial.begin(115200);
 pinMode(s0,OUTPUT);
 pinMode(s1,OUTPUT); 
 pinMode(s2,OUTPUT);
 pinMode(s3,OUTPUT);

 }
void TCS()
 {
 flag=0;  
 digitalWrite(s1,HIGH);
 digitalWrite(s0,HIGH);
 digitalWrite(s2,LOW);
 digitalWrite(s3,LOW);
 attachInterrupt(0, ISR_INTO, CHANGE);
 timer0_init();

 }
void ISR_INTO()
 {
 counter++;
 }
 void timer0_init(void)
 {
  TCCR2A=0x00;
  TCCR2B=0x07;   //the clock frequency source 1024 points
  TCNT2= 100;    //10 ms overflow again
  TIMSK2 = 0x01; //allow interrupt
 }
 int i=0;
 ISR(TIMER2_OVF_vect)//the timer 2, 10ms interrupt overflow again. Internal overflow interrupt executive function
{
    TCNT2=100;
    flag++;
 if(flag==1)
  {
    countR=counter;
    Serial.print("red=");
    Serial.println(countR,DEC);
    digitalWrite(s2,HIGH);
    digitalWrite(s3,HIGH);
  }
  else if(flag==2)
   {
    countG=counter;
    Serial.print("green=");
    Serial.println(countG,DEC);
    digitalWrite(s2,LOW);
    digitalWrite(s3,HIGH);
   }
   else if(flag==3)
    {
    countB=counter;
    Serial.print("blue=");
    Serial.println(countB,DEC);
    Serial.println("\n"); 
    digitalWrite(s2,LOW);
    digitalWrite(s3,LOW);
   
    }
    else if(flag==4)
     {
     flag=0;
     }
       counter=0;
}
void loop()
 {
  TCS();
while(1);
 }

Result

Color compare en1.png

Data exists deviation, you need to adjust the program according to environmental parameters

Trouble shooting

More question and cool idea, visit DFRobot Forum

More


Nextredirectltr.pngClick to buy TCS3200 GBB Color Sensor For Arduino

Nextredirectltr.pngDFRobot Distributor List

Category: DFRobot > Sensors &Modules >Sensors > Light & Imaging Sensors