Gravity: Digital 5A Relay Module Introduction
The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most common applications with Arduino are: Home lighting, electrical appliances of high power and other equipments. The modular design makes it easy to integrate with a controller board. The Relay integrates a status LED, in order to acknowledg..
4 Channel Relay Shield for Arduino Introduction
This Relay Shield for Arduino acts like a switch. It is commonly used to control anything over 5V such as lamps, water pumps and garage doors. One of the most interesting projects for your boards is perhaps being able to control High power devices like Lamps, water pumps, garage doors and so on. But interfacing with high power and AC is quite a dangerous task when building the ..
8 Channel Ethernet Relay Controller (Support PoE and USB) Introduction With Ethernet relay, IoT(Internet of things) has become so easy. RLY-8-POE-USB is a POE & USB controlled 8 channel relay controller based on STM32. With this module users are able to do remote control/ switching power supply centralized management, the purpose of this product can be directly by net POE power supply switch power supply is connected to the Internet, so you..
8 Channel IoT Ethernet Relay Controller (Support PoE and RS485) Introduction
The RLY-8 is a network relay controller with open source communication protocol. It integrates 8 channel relays and each relay is able to stand 277VAC-10A or 125VAC-12A power. Since most of the household appliances are under 250VAC, this means you can use the RLY-8 relay almost everywhere!
The RLY-8 uses a STM32 microcontroller. It supports 2 types of power supply: Wall adapter o..
Accessory Shield for Arduino Introduction This Accessory Shield for Bluno is specially designed for Bluno (BLE with Arduino Uno), which is first of its kind in intergrating BT 4.0(BLE) module into Arduino Uno. It also compatible with standard Arduino Uno. With Bluno, this Accessory Shield forms an ideal prototyping platform for both software and hardware developers to go wireless. You will be able to develop your own s..
Gravity: Digital 10A Relay Module (Arduino and Raspberry Pi Compatible) Introduction
Introducing the Gravity Digital Relay Module – the latest addition to DFRobot’s Gravity series! This module is a little different to the other relays in our store - not only is it compatible with 5V Arduino boards, but also with Raspberry Pi, BBB (BeagleBoard Black), mbed, Intel Joule, Arduino 101 and other 3.3V devices.
It is specially designed for low-voltage devices and works wel..
Gravity: Digital 16A Relay Module Introduction
A relay is an electrically operated switch, which has a control system (also known as the input circuit) and the controlled system (also known as the output circuit), usually used in automatic control circuit. It is actually "automatic switch", using a small electric current to control a larger current.Therefore, the relay has the effects on the automatical automatic adjustment, ..
Gravity: MOSFET Power Controller Introduction
In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the internal coil to pick-up contact. But for some MCU, like Intel Edison, Intel joule, lilypad, Raspberry Pi and other microcontroller with limited amount of current GPIO, it’s hard to drive one or more relays simultaneously.
The MOSFET power ..
USB - RLY 16 16Amp, 8 Channel Relay Module Introduction
The USB-RLY16 provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The processor is powered and instructed from any standard USB bus and the relay power is obtained by the DC power input adaptor. The DC input jack is 2.1mm with positive core polarity, DC supplies are required to supply at least 500mA at 12vdc. The relays are SPCO (Single Pole Ch..
USB-RLY16L(16 Low Power 8 channel relay outputs at 16A) Introduction
A low power version of the USB-RLY16 module, the USB-RLY16L is powered solely from the USB bus and provides eight volt free contact relay outputs with a current rating of up to 16Amp each. The relays are SPCO (Single Pole Change Over) types and provide position 0, position 1 and common pins (latching relays and have no "normally open" or "normally closed" contacts) on the scr..
Xboard Relay - An Ethernet Controllered Relay Introduction
Internet of things has become so easy. With Xboard Relay, you can not only monitor data through internet, but also control it through internet. The Xboard Relay combines an Atmega 32u4 microprocessor and wiz5100 chip which is fully compatible with Arduino Lendardo and Ethernet library, it has build-in Xbee socket and 2 Relays which allow an easy sensoring and cont..
Out Of Stock
Ethernet Controlled 8 Channel Relay 16A Introduction
The ETH008 provides eight volt free contact relay outputs with a current rating of up to 16Am. The module is powered from a 12vdc supply which can be regulated or unregulated. The DC input jack is 2.1mm with positive core polarity, DC supplies are required to supply at least 500mA at 12vdc. The relays are SPCO (Single Pole Change Over) types.
The normally open, normally closed a..