Topics

822 Views

1 Replies
We keep getting the output "bme begin failed, device not detected" I have checked the ICP addresses multiple times and tried different pins. FAQ SEN0335 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:22

5429 Views

1 Replies
When will the pi 5 8GB start shipping FAQ DFR1119 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:22

869 Views

1 Replies
Hallo, Is there a tax fee for shipping to Indonesia? FAQ SEN0343 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:22

713 Views

1 Replies
Hello, in the product wiki, the following is mentioned: "RS485 requires 2 terminal resistors, and its resistance value must be equal to the characteristic impedance of the transmis... FAQ DFR0779 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:22

537 Views

1 Replies
Does this sensor read oil? FAQ SEN0485 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:22

873 Views

1 Replies
Hi, I bought the sensor 6 months back and now the reading is stuck at 0.01ppm and not increasing even while interfering with alcohol. What should I do? FAQ SEN0376 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

596 Views

1 Replies
I purchased this product, and it is drawing significantly more than 125 mA at 5V. It's drawing closer to 600 mA. I don't want to drive it beyond specs, so could you please clarify ... FAQ DFR0800 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

631 Views

1 Replies
Hello! Do you have more code example for this product?How two arduino board can communicate on this board?Bought it few years ago, but not enough information to use it! Please make... FAQ DFR0271 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

566 Views

1 Replies
Do you have some examples how to connect and drive DC motors with encoders from your stock? FAQ DRI0004 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

627 Views

1 Replies
Raspberry pi 4 , model B FAQ DFR0738 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

529 Views

1 Replies
Hello, my module does not light up until the voltage is over 4.30 V. What could cause this? Can it be fixed? FAQ DFR0673 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

653 Views

1 Replies
Very nice. Can the 3 pin plug be specified, and with compatible cables/plug. references.. Be nice to have a dual 3-pin to a single 4pin PH 2.0 plug be available. FAQ DFR0996 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

820 Views

1 Replies
Is there an arduino library for this product? Does this library work with it? https://github.com/DFRobotd...Most importantly, is there a way to adjust the sensitivity parameters... FAQ SEN0557 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

853 Views

1 Replies
What is the encoder hall sensor specs? Part number or datasheet links? FAQ FIT0450 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

744 Views

1 Replies
Hi, I'm considering using this for atmospheric composition measurements. Can this detect ppb level concentrations? FAQ SEN0471 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

617 Views

1 Replies
what should I do to make this amplifier withstand 200W, can I put a 2ohm speaker in it? FAQ DFR0675-EN SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

567 Views

1 Replies
this module work in 2g? or 3g? FAQ TEL0134 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:21

634 Views

1 Replies
I interest the M.2 ethernet card,it's a new product of dfrobot? Can you provide me 3D file ?Thank's in advance FAQ FIT0798 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:20

624 Views

1 Replies
Hello,it's possible to reduce the fov at 8°?With 15° the measure is good untill 1.50m, after, for 2.00 the measure are 1.70 to 2.20m.Thank You very much. https://uploads.disquscdn.... FAQ SEN0337 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:20

624 Views

1 Replies
Are the resulting points from a scan with this all on the same plane? Therefore if I wanted to collect 3d data I would have to tilt or move the sensor, correct? FAQ DFR1022 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:20

Topics

Trending