Topics

86 Views

0 Replies
Great product design! Only thing I would add is VESA mounting points for standardized mounting. FAQ DFR0711 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

45 Views

3 Replies
How exactly do you connect to this? I see the two metal rings on the backside but no connector. Can we just hook up two wires to it or is there a specific connector we have to use? FAQ FIT0333 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

117 Views

3 Replies
Can it only be controlled with PPM or will a PWM signal from an RC receiver work too? Also, is it suitable for 6s lipos which have a fully charged voltage slightly over 24V? FAQ DRI0047 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

45 Views

3 Replies
Please tell me you guys are going to make a Pico Beetle!! FAQ DFR0817 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

86 Views

30 Replies
Very nice product ! FAQ DFR0745 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

61 Views

6 Replies
This would have been very nice if the connectors had not been placed in such a stupid place, sticking out on the side? No good way to integrate and very exposed when sitting on a d... FAQ DFR0698 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

66 Views

8 Replies
Is there, or will there be, a case for this screen - Rpi3 and for the RPi4? FAQ DFR0678 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

76 Views

0 Replies
Hi, if I use 4 of these sensors for my Arduino mega, do I have to use a 10K resistor for each sensor? or can I just use 1 and jumper it to the signal wires? FAQ SEN0164 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

1618 Views

1 Replies
Does the devastator come with plastic or metal gears? FAQ SEN0305-2 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

70 Views

0 Replies
Is it okay to connect the thermal pad to GND? FAQ DFR0753 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

113 Views

0 Replies
Hi, what's the dimensions of this? FAQ DFR0106 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

48 Views

9 Replies
Here's what you need to know to make this gadget work:Pins:Vcc | Vcc (compatible with 3.3v or 5v power)PWM1 | PWM2 (PWM input for motors 1 and 2)INA1 | INA2 (motors 1 and 2 control... FAQ SEN0307 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

109 Views

0 Replies
Does it include batteries and usb cable? FAQ MBT0039 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

78 Views

0 Replies
This sensor looks great except that it doesn't do well with human detection. The 7051 does well with human (soft targets) detection but it doesn't output the analog signal. Is ther... FAQ SEN0282 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

48 Views

4 Replies
Not being knowledgeable of certain devices, so I ask. Q: Can I use this to have a USB connection for a thumb drive? With the prices of thumb drives (USB 1.1, 2.0 and 3.0) so low an... FAQ TEL0010 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

66 Views

13 Replies
What material is the sensor coating made of? FAQ SEN0308 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

46 Views

0 Replies
That look like a good case....BUT I am missing a push-button to connect to a GPIO in order to perform a shutdown, since most of my projects are headless and sometimes not even on L... FAQ DFR0621 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

534 Views

1 Replies
what spline does this servo have FAQ SER0046 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

120 Views

0 Replies
I like this button PCB, but I prefer square keytops to round ones. I would like to change the keytop, can I know the manufacturer of tact switch? FAQ DFR0029-R SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

61 Views

2 Replies
Is there a code written for this bionic arm someone can share? Thanks FAQ ROB0143 SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:17

Topics

Trending