Topics

486 Views

0 Replies
XDK code works on Edison but fails on Romeo v1.0 - port mapping issue? DFR0331 DFR0350 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

500 Views

0 Replies
I can't debug via COM port without OTG plugged. DFR0331 DFR0350 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

454 Views

0 Replies
Win XP/ Win 7 incompatible issue. DFR0331 DFR0350 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

543 Views

0 Replies
why does first calibration always fail? DFR0300 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

1196 Views

0 Replies
DFR0300Calibration: must I do two points or is one point enough? DFR0300 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

596 Views

0 Replies
First calibration attempt gives erratic readings - why? SEN0161-V2 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

574 Views

0 Replies
1-point vs 2-point calibration: required? SEN0161-V2 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

3724 Views

0 Replies
DF, how long does the probe need to be calibrated? SEN0161-V2 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

503 Views

0 Replies
Leonardo GPS AT commands: Serial vs Serial1 adaptation? TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

413 Views

0 Replies
Can this module support FTP, if yes, how? TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

502 Views

0 Replies
Shield LEDs turn off when serial connects - 'normal power off' response TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

442 Views

0 Replies
How to make 0.5 mol/L NaOH solution? SEN0237 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

665 Views

0 Replies
Built-in temp sensor? How to enable compensation? SEN0244 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

666 Views

0 Replies
How to properly store the pH probe? SEN0249 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

2622 Views

0 Replies
Hi DF, how long does the probe need to be calibrated? SEN0249 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

433 Views

0 Replies
Serial warns 'Normal power down' & LEDs off after reconnect TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

468 Views

0 Replies
Serial errors 103/104: Stop bit timing issues - fix? TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

427 Views

0 Replies
What's the minutes and seconds of coordinate data? TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

490 Views

0 Replies
GSM USB mode: Ctrl+Z sends entire screen content TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

456 Views

0 Replies
If the module is not working properly, plz check TEL0051 FAQ SEO FAQ Aftersales FAQ JaneYu 2026-02-14 08:57:29

Topics

Trending